Navigation

Object Detection

matchTemplate

Compares a template against overlapped image regions.

C++: void matchTemplate(InputArray image, InputArray templ, OutputArray result, int method)
Python: cv2.matchTemplate(image, templ, method[, result]) → result
C: void cvMatchTemplate(const CvArr* image, const CvArr* templ, CvArr* result, int method)
Python: cv.MatchTemplate(image, templ, result, method) → None
Parameters:
  • image – Image where the search is running. It must be 8-bit or 32-bit floating-point.
  • templ – Searched template. It must be not greater than the source image and have the same data type.
  • result – Map of comparison results. It must be single-channel 32-bit floating-point. If image is W \times H and templ is w \times h , then result is (W-w+1) \times (H-h+1) .
  • method – Parameter specifying the comparison method (see below).

The function slides through image , compares the overlapped patches of size w \times h against templ using the specified method and stores the comparison results in result . Here are the formulae for the available comparison methods ( I denotes image, T template, R result ). The summation is done over template and/or the image patch: x' = 0...w-1, y' = 0...h-1 * method=CV_TM_SQDIFF

R(x,y)= \sum _{x',y'} (T(x',y')-I(x+x',y+y'))^2

  • method=CV_TM_SQDIFF_NORMED

    R(x,y)= \frac{\sum_{x',y'} (T(x',y')-I(x+x',y+y'))^2}{\sqrt{\sum_{x',y'}T(x',y')^2 \cdot \sum_{x',y'} I(x+x',y+y')^2}}

  • method=CV_TM_CCORR

    R(x,y)= \sum _{x',y'} (T(x',y') \cdot I(x+x',y+y'))

  • method=CV_TM_CCORR_NORMED

    R(x,y)= \frac{\sum_{x',y'} (T(x',y') \cdot I(x+x',y+y'))}{\sqrt{\sum_{x',y'}T(x',y')^2 \cdot \sum_{x',y'} I(x+x',y+y')^2}}

  • method=CV_TM_CCOEFF

    R(x,y)= \sum _{x',y'} (T'(x',y') \cdot I'(x+x',y+y'))

    where

    \begin{array}{l} T'(x',y')=T(x',y') - 1/(w \cdot h) \cdot \sum _{x'',y''} T(x'',y'') \\ I'(x+x',y+y')=I(x+x',y+y') - 1/(w \cdot h) \cdot \sum _{x'',y''} I(x+x'',y+y'') \end{array}

  • method=CV_TM_CCOEFF_NORMED

    R(x,y)= \frac{ \sum_{x',y'} (T'(x',y') \cdot I'(x+x',y+y')) }{ \sqrt{\sum_{x',y'}T'(x',y')^2 \cdot \sum_{x',y'} I'(x+x',y+y')^2} }

After the function finishes the comparison, the best matches can be found as global minimums (when CV_TM_SQDIFF was used) or maximums (when CV_TM_CCORR or CV_TM_CCOEFF was used) using the minMaxLoc() function. In case of a color image, template summation in the numerator and each sum in the denominator is done over all of the channels and separate mean values are used for each channel. That is, the function can take a color template and a color image. The result will still be a single-channel image, which is easier to analyze.

Table Of Contents

Previous topic

Feature Detection

Next topic

highgui. High-level GUI and Media I/O

This Page

Navigation

© Copyright 2011-2012, opencv dev team. Last updated on Nov 03, 2012. Created using Sphinx 1.0.7.